Aspen FLX 627 LSO Adjustable Size Lumbar Brace For Lower Back Pain Relief - Aspen FLX 627 LSO 可調節尺寸腰椎支架，緩解腰背部疼痛

Description:

Enhancing the proven design and function of the OTS product line, the FLX line of inelastic braces offers a conservative treatment solution for patients experiencing lower back pain. Structural improvements have been added to enhance stability and support while maintaining a sleek, breathable profile. These one-size adjustable braces are flexible by design, providing targeted compression and stability to support patients and aid in pain relief.

Instruction:

1. SIZE ADJUSTMENT

A. To adjust the size of the brace, peel up the inside end of each side panel.

B. Adjust as necessary to achieve a proper fit and reattach.

C. Brace sizes follow closely to standard pants sizes. Size ranges are only guidelines.

NOTE: Once the brace is applied, the sides of the brace may require further adjustment to achieve a snug fit without too much overlap at the front of the brace.

2. PREPARATION

A. Place the pull tabs 2 inches (5 cm) from the plastic in the back of the brace. Pull the

ends of the brace away from each other ensuring that the brace is fully extended.

FLX 637:

B. With brace extended fully, place one lateral panel on midline on each side panel of the

brace. Press down to secure to brace.

C. When Horizon brace is properly fit to the patient, the lateral panels should fit at

patient’s midline.

3. APPLICATION

A. Apply the fully extended brace making sure the back panel is centered and low on

the back.

B. Apply the brace tightly, with the right side overlapping the left. When applied properly,

both the upper and lower edge of the brace should be snug. If they are not, reapply the

brace. If needed, angle the ends to insure a snug fit at both the upper and lower edges.

NOTE: For certain patients, the ends must be steeply angled.

4. TIGHTENING

A. Slip your thumbs through the holes in the pull tabs. Pull away from your body.

B. The left pull tab controls lower compression and the right pull tab controls the upper

compression. Adjust the compression as needed.

C. When tightened, secure the pull tabs to the loop in front of the brace.

5. ADJUSTMENT

A. Adjust the upper and/or lower compression by loosening or tightening the pull tabs

as needed.

B. When patient is seated, slightly loosening the upper portion may be beneficial.

6. MODIFICATION OPTIONS

This product may be substantially modified by an individual with expertise. 

INTENDED USE

To provide motion restriction and stability of the lumbar-sacral spine.

INDICATIONS

Postoperative support, Deconditioned trunk musculature, Post laminectomy syndrome,

Surgical Decompression procedures, Non-surgical Decompression procedures,

Degenerative disc disease, Bulging or herniated disc, Non-specific low back pain,

Chronic low back pain, Fracture management, Spondylolysis, Spondylolisthesis, Spinal

stenosis, Ligament sprains / Muscle strains, Spondylosis (Osteoarthritis/Degenerative

Joint Disease), Facet syndrome, SI dysfunction, Sacroiliitis, Radiculopathy, Injections,

Radiofrequency Ablation, Lumbar Multifidus Muscle Atrophy.

CONTRAINDICATIONS

Hypersensitivity or allergies to any of the materials from which the brace is made.

Swelling of the lymphatic tissue caused by circulatory disorders. Patients who are not

allowed to wear a brace according to medical instructions.

PRECAUTIONS

READ INSTRUCTIONS BEFORE USE. Proper training in the use of this device should

take place before it is applied. These directions are guidelines only and are not offered

as medical recommendations. If you suffer from a serious medical condition, we

strongly suggest that you consult with a licensed health care professional before using

this product. Proper fitting is required for this product to be effective. Under some

circumstances, this product may be prescribed by a physician. Please see the limited

warranty for further information.

CARE INSTRUCTIONS

Hand wash only at 30° C; Wash with mild detergent; Air dry; Do not use bleach or other

chemicals

MATERIALS

Nylon, Polyester, HDPE, PVC, Polyurethane, UHMWPE.

NOT MADE WITH NATURAL RUBBER LATEX.

增強了 OTS 產品線的設計和功能，FLX 系列的無彈性支架為腰痛患者提供了保守的治療解決方案。結構改進增強了穩定性和支撐性，同時保持簡潔透氣的外形設計。這些可調整大小的支架具有靈活設計，提供針對性的壓縮和穩定性，以支援患者並幫助緩解疼痛。

使用說明：

1. 調整尺寸

   A. 要調整支架尺寸，撕開每個側面板內側的末端。

   B. 根據需要進行調整以達到合適的貼合並重新固定。

   C. 支架尺寸接近標準褲子尺碼。尺寸範圍僅作為指導。

   注意：支架佩戴後，可能需要進一步調整側邊以確保前面沒有過多重疊。

2. 準備

   A. 將拉帶放置在支架後部的塑膠2英寸（5公分）處。將支架兩端向相反方向拉，確保支架完全伸展。

   FLX 637：

   B. 在完全展開支架的情況下，將一個側板放置在每個側面板的中線上。按下以固定在支架上。

   C. 當支架適合患者時，側板應位於患者的中線處。

3. 應用

   A. 應用完全展開的支架，確保背板居中並位於背部下方。

   B. 牢固地佩戴支架，右側重疊左側。佩戴正確時，支架的上下邊緣應緊貼。如果不緊，重新佩戴支架。如有需要，調整兩端的角度以確保上下邊緣緊貼。

   注意：對於某些患者，兩端必須急劇傾斜。

4. 緊固

   A. 將拇指插入拉帶的孔中，向身體外側拉。

   B. 左側拉帶控制下部壓縮，右側拉帶控制上部壓縮。根據需要調整壓縮。

   C. 緊固後，將拉帶固定在支架前面的環上。

5. 調整

   A. 根據需要通過鬆開或緊固拉帶來調整上部或下部的壓縮。

   B. 當患者坐著時，稍微鬆開上部可能有助於舒適度。

6. 修改選項

   專業人士可以對此產品進行重大修改。

適用範圍

提供腰骶部脊柱的活動限制和穩定性。

適應症

術後支持、軀幹肌肉群失調、椎板切除術後綜合症、外科減壓手術、非手術減壓手術、退化性椎間盤疾病、椎間盤膨出或突出、非特異性下背痛、慢性下背痛、骨折管理、脊椎崩裂症、脊椎滑脫、椎管狹窄、韌帶扭傷 / 肌肉拉傷、脊椎病（骨關節炎/退化性關節病）、關節綜合症、骶髂關節功能障礙、骶髂關節炎、神經根病、注射、射頻燒灼、腰部多裂肌萎縮。

禁忌症

對支架材料過敏的患者。因循環系統問題導致淋巴腫脹的患者。根據醫療指示不允許佩戴支架的患者。

注意事項

使用前請閱讀說明。應在使用此設備之前進行適當的培訓。此說明僅作為指導，不構成醫療建議。如有嚴重健康狀況，我們強烈建議您在使用本產品之前諮詢持牌醫療專業人士。正確的適配對此產品的效果至關重要。在某些情況下，可能由醫師開具處方。請參閱有限保修了解更多信息。

護理說明

僅可手洗，水溫不超過30°C；用溫和清潔劑清洗；風乾；請勿使用漂白劑或其他化學品。

材質

尼龍、聚酯纖維、HDPE、PVC、聚氨酯、UHMWPE。

不含天然橡膠乳膠。